Skip to content
AdasXADAS Calibration & Programming

Guide

ADAS calibration for electric and hybrid vehicles

Electric and hybrid vehicles use the same kinds of ADAS sensors as other vehicles: forward cameras, front and corner radar, surround-view cameras and parking sensors. The calibration principles are the same too. The manufacturer's procedure for the specific vehicle decides whether calibration is needed after a repair, which method applies and what conditions the vehicle must be in, which can include how it's powered during the procedure.

Electric vehicle parked at a charging station

Key takeaways

  • EVs and hybrids use the same kinds of ADAS sensors as other vehicles.
  • The manufacturer's procedure decides when calibration is required and the conditions the vehicle must be in.
  • A stable power supply during calibration matters, and EVs may have specific power-mode instructions.
  • Calibration doesn't involve high-voltage components, but nearby body repairs follow the manufacturer's safety procedures.

What's the same as any other vehicle

A camera behind the windshield still needs to know exactly where it points. A radar behind the front fascia still needs to be aimed correctly. Windshield replacement, bumper and mirror work, wheel alignment and collision repairs can all affect those sensors, and the manufacturer's repair information decides whether calibration is required. Static, dynamic and combined procedures all apply, depending on the vehicle.

Where EV front ends differ

Many electric vehicles don't need a large front grille for engine cooling, so the front of the vehicle may be a smooth fascia. The front radar is still there on equipped vehicles, often behind the fascia or a flat panel designed for the radar signal to pass through. That means front-end repairs and refinishing can affect the radar in the same way bumper and grille work does on other vehicles. The repair information shows where the sensors are.

Powering the vehicle during calibration

Calibration procedures often run with the vehicle switched on for an extended time, and a stable voltage helps the modules complete the procedure. Many manufacturers specify supporting the 12-volt battery during long scan and calibration procedures. Electric and hybrid vehicles may also have specific instructions for the power mode or ready state during the procedure. We follow the conditions listed in the procedure for the vehicle.

High-voltage safety

ADAS calibration works with cameras, radar and the diagnostic port. It doesn't involve opening high-voltage components. Collision and body repairs near high-voltage parts, however, follow the manufacturer's safety procedures and are handled by technicians trained for that work. Calibration is scheduled once those repairs are complete and the vehicle is safe to operate.

Prerequisites that still apply

  • Correct tire pressures and the tire sizes specified for the vehicle
  • A completed wheel alignment where the procedure lists it
  • Normal ride height and an unloaded vehicle, where specified
  • Repairs to sensors, brackets, glass and bumpers completed first
  • A stable power supply for the duration of the procedure

Weight and ride height

Electric vehicles carry heavy battery packs, and the vehicle's ride height and suspension condition affect where sensors point relative to the road. Suspension repairs, ride-height changes or worn components can affect calibration on any vehicle. Where the procedure specifies measuring ride height or checking suspension condition, that's done before the calibration.

Software and updates

Many electric vehicles receive software updates, and ADAS modules can be part of that. A calibration may depend on a module having the software level the manufacturer specifies, or a newly installed sensor may need programming or configuration before it can be calibrated. A scan helps identify whether a module reports a configuration or software issue.

Dynamic drives in an EV

Where a dynamic calibration is specified, the vehicle is driven under the manufacturer's conditions, such as speed range, clear lane markings and suitable traffic, with a scan tool connected. Weather and road conditions affect electric and gas vehicles alike, so timing may depend on conditions.

Repairs that commonly lead to an EV calibration

  • Windshield replacement on a vehicle with a windshield-mounted camera
  • Front fascia, bumper or radar panel repair or refinishing
  • Side mirror replacement where the mirror contains a surround-view camera
  • Rear bumper or tailgate work near corner radar, parking sensors or the rear camera
  • Wheel alignment, suspension work or tire size changes

Booking an EV or hybrid calibration

Send the make, model and year, the VIN if available, the repair performed and any warning messages. Mention the vehicle's charge level and whether it can be powered for the duration of the appointment. AdasX calibrates on-site at businesses in Mississauga, Oakville and Burlington and confirms compatibility for each vehicle before booking.

What to expect when you book

  1. Send the vehicle details: make, model, year, VIN if available, and the repair performed.
  2. We confirm compatibility, the required procedure, pricing, location and appointment availability.
  3. We arrange on-site service at your approved business location, with the space and conditions the procedure needs.
  4. We complete the applicable calibration procedure and provide the service documentation available for that vehicle.

Documentation

We complete the applicable calibration procedure and provide the service documentation available for that vehicle.

Frequently asked questions

Is ADAS calibration different on an electric vehicle?

The principles are the same. Each vehicle has its own procedure, which can include specific conditions such as how the vehicle must be powered during the calibration.

Does an EV without a grille still have front radar?

Many equipped EVs do, typically behind the front fascia or a panel designed for the radar signal. The repair information for the vehicle shows where it is.

Do you need to work on the high-voltage system?

No. Calibration uses the cameras, radar and diagnostic port. High-voltage repairs are separate work done by trained technicians following the manufacturer's procedures.

Should the EV be charged before the appointment?

It helps to have enough charge for the vehicle to stay powered during the procedure and, if a dynamic calibration is needed, for the road drive. We confirm what's needed when we book.

Need a calibration at your shop?

Call or text AdasX with the vehicle details. We'll confirm compatibility, the required procedure, pricing and availability.

Request Service

Tell us what you need and we'll confirm compatibility, pricing and availability. Prefer to talk? Call or text 647-967-2647.