Skip to content
AdasXADAS Calibration & Programming

Guide

Static vs dynamic ADAS calibration

Static calibration is done with the vehicle stationary, using targets placed at precise distances and heights. Dynamic calibration is done on the road with a scan tool connected, under the conditions the manufacturer specifies. Some systems need both stages. The vehicle manufacturer's procedure decides which one applies.

Key takeaways

  • Static calibration uses targets with the vehicle stationary. Dynamic calibration uses a road drive with a scan tool connected.
  • Some systems need both stages, in the order the manufacturer specifies.
  • The manufacturer's procedure, not the workshop, decides which method applies.
  • Both methods depend on prerequisites such as tire pressures, alignment and suitable conditions.

Static calibration

Static calibration is carried out with the vehicle stationary. Targets are positioned at precise distances and heights in front of or around the vehicle, and a scan tool guides the sensor through the procedure. It needs suitable conditions: typically level ground and enough clear space around the vehicle for the targets. Requirements vary by vehicle, and we confirm them before booking.

Dynamic calibration

Dynamic calibration is done on the road. With a scan tool connected, the vehicle is driven under the conditions the manufacturer specifies, such as speed, road markings and traffic, until the system completes its calibration. Procedures often need clear lane markings and suitable conditions, so weather can affect timing.

Combined static and dynamic

Some manufacturers specify an initial target-based alignment followed by an on-road learning drive. Skipping either stage can leave the system incomplete, so we complete both when the procedure requires it.

Before either procedure

Some vehicles or procedures need specific conditions, such as level ground, clear space around the vehicle, correct tire pressures, a completed wheel alignment, or additional repairs before calibration can be completed. We'll tell you what's needed when we confirm the job.

Which systems usually use which method

  • Forward cameras: static, dynamic or both, depending on the manufacturer
  • Front radar for adaptive cruise and emergency braking: often static, with some needing a confirmation drive
  • Blind-spot and rear corner radar: static or dynamic, depending on the vehicle
  • Surround-view and 360° cameras: usually target-based, with mats or boards placed around the vehicle

Why one method can't replace the other

The procedure is written by the vehicle manufacturer for that specific sensor. If the procedure calls for targets, a road drive alone won't complete it, and if it calls for a learning drive, a target setup alone may leave the system unfinished. Picking the method to suit the workshop rather than the vehicle is one of the most common reasons a calibration has to be redone.

How long each takes

Timing depends on the vehicle and the number of systems involved. Static procedures include the time needed to set up and measure targets. Dynamic procedures depend on finding the road and traffic conditions the system needs, which is why weather and lane markings can affect timing. We give a time estimate when we confirm the job.

What a static setup involves

  • Confirming the vehicle is level, at correct tire pressures and free of unusual load
  • Measuring the vehicle's centreline and positioning targets at the specified distance and height
  • Running the procedure from a scan tool, which guides the sensor until it accepts the new position
  • Post-scanning to confirm the system reports no remaining faults

What a dynamic drive involves

A scan tool is connected and the calibration is started, then the vehicle is driven at the speeds and on the kind of road the manufacturer specifies, often with clear lane markings and other traffic for the sensor to read. The system reports when it has completed its learning. If conditions aren't right, the drive can take longer or need to be repeated.

What to expect when you book

  1. Send the vehicle details: make, model, year, VIN if available, and the repair performed.
  2. We confirm compatibility, the required procedure, pricing, location and appointment availability.
  3. We arrange on-site service at your approved business location, with the space and conditions the procedure needs.
  4. We complete the applicable calibration procedure and provide the service documentation available for that vehicle.

Documentation

We complete the applicable calibration procedure and provide the service documentation available for that vehicle.

Frequently asked questions

Is static or dynamic calibration better?

Neither is better in general. Each sensor has a procedure written by the vehicle manufacturer, and that procedure specifies static, dynamic or both. The right method is the one the procedure calls for.

Can dynamic calibration be done in the rain or snow?

Dynamic procedures usually need clear lane markings and suitable road and traffic conditions. Heavy rain, snow or covered lane lines can stop a calibration from completing, so weather can affect timing.

What space does a static calibration need?

Typically level ground and enough clear space in front of and around the vehicle for the targets at their specified distances. Requirements vary by vehicle, and we confirm them before booking.

How do I know the calibration finished?

The scan tool reports when the procedure is complete, and a post-scan confirms the system has no remaining faults. We provide the service documentation available for that vehicle.

Need a calibration at your shop?

Call or text AdasX with the vehicle details. We'll confirm compatibility, the required procedure, pricing and availability.

Request Service

Tell us what you need and we'll confirm compatibility, pricing and availability. Prefer to talk? Call or text 647-967-2647.