
Key takeaways
- Plan ADAS calibration at the estimate, using the VIN and the manufacturer's repair information.
- Calibrate after repairs, reassembly and alignment, then post-scan before the keys go back.
- Book mobile calibration for when the vehicle will be ready, and send the details ahead of time.
- Keep scan and calibration records with the repair order.
Start at the estimate
The estimate is where calibration requirements are cheapest to find. Decode the VIN to identify which ADAS features the vehicle has, then compare the parts on the estimate with the manufacturer's repair information. A windshield, front bumper, grille, mirror, rear bumper or alignment on the estimate is a prompt to check whether the procedure calls for a calibration or a check. Noting it at this stage helps with parts ordering, scheduling and the conversation with the customer and insurer.
A typical sequence, estimate to keys back
- Estimate: identify ADAS equipment and research the procedures for the parts involved
- Pre-scan: record existing codes before repairs begin
- Parts: order parts that match the manufacturer's information for sensor-equipped areas
- Repair: complete structural, body and mechanical repairs, including sensors and brackets
- Refinish: follow any guidance on refinishing near radar sensors
- Alignment: complete the wheel alignment and steering angle reset where specified
- Calibration: calibrate the systems the procedure requires
- Post-scan and road test: confirm no faults remain and the systems operate
- Documentation: file the scan and calibration records with the repair order
Why order matters
Calibrations depend on the vehicle being in its repaired condition. A camera calibrated before the windshield urethane has cured according to the glass manufacturer's guidance, or a radar calibrated before the bumper is fully installed, may need to be repeated. A calibration done before the alignment can complete against the wrong reference. Scheduling calibration after the work it depends on avoids comebacks and repeat visits.
Scheduling mobile calibration
With a mobile provider, the calibration comes to the vehicle. The shop can book the visit for when the repair, alignment and reassembly are expected to be finished, and group several vehicles into one visit where the schedule allows. Send the vehicle details ahead of time so the procedure, targets and site requirements are confirmed before arrival, and tell the provider if the timing changes.
Preparing the vehicle and the space
- Repairs, reassembly and alignment are complete
- Tire pressures are set to specification and the vehicle is unloaded where required
- The fuel level or charge meets the procedure's requirements, where listed
- A battery support unit or stable power is available for longer procedures
- There's level ground and clear space around the vehicle for static targets
- Keys and any access to the vehicle's settings are available
When the calibration is part of the estimate
Including scanning and calibration on the estimate, with a reference to the manufacturer's repair information, helps explain why it's needed. Insurers and customers generally want to see that the step comes from the vehicle's procedure rather than habit. A calibration record and post-scan afterward show it was done.
Handling surprises
Sometimes a pre-scan or the calibration itself reveals something new: a damaged bracket, a sensor fault, a part that doesn't fit correctly or a module needing software. When that happens, the shop addresses the cause, and the calibration is completed once the repair is done. Leaving buffer time in the schedule for ADAS-heavy repairs makes these less disruptive.
What to record
- Pre-scan and post-scan reports
- The calibrations performed, the method used and the result
- The prerequisites checked, such as alignment and tire pressure
- Any parts replaced in sensor-equipped areas
- Road test notes where the procedure includes one
Working with AdasX
AdasX provides on-site calibration for collision repair facilities in Mississauga, Oakville and Burlington. A post-collision ADAS assessment starts from $249 and multi-system calibration from $399, quoted per vehicle. Send the estimate or parts list, and we'll confirm the procedures and plan the visit around your schedule.
What to expect when you book
- Send the vehicle details: make, model, year, VIN if available, and the repair performed.
- We confirm compatibility, the required procedure, pricing, location and appointment availability.
- We arrange on-site service at your approved business location, with the space and conditions the procedure needs.
- We complete the applicable calibration procedure and provide the service documentation available for that vehicle.
Documentation
We complete the applicable calibration procedure and provide the service documentation available for that vehicle.
Frequently asked questions
When should the calibration be booked?
Once you know which systems are involved and roughly when repairs and alignment will be finished. Booking early and confirming the timing as the job progresses works best with a mobile provider.
Does every collision repair need calibration?
No. It depends on the vehicle, its equipment and the parts repaired. The manufacturer's repair information for the work performed decides it.
Can several vehicles be calibrated in one visit?
Yes, where the schedule allows and there's space. Send the list of vehicles and the work involved, and we'll plan the visit.
What if the calibration reveals another problem?
We'll explain what the scan or procedure shows. The shop addresses the cause, and the calibration is completed once it's resolved.