Key takeaways
- ADAS sensors are aimed for the vehicle's designed ride height.
- Lifting, lowering, tire size changes and suspension repairs can change sensor aim.
- Complete the wheel alignment before calibration.
- Heavily modified vehicles may not meet every manufacturer procedure, so they're assessed case by case.
Why ride height matters to ADAS
A forward camera behind the windshield and a radar in the front bumper are both set up to look at the road at a specific angle. That angle assumes the vehicle sits at its designed height, front to rear and side to side. If the front is raised or the rear lowered, the sensors tilt with the body. A camera tilted upward may look past lane markings that it should be reading, and a radar tilted downward may see the road surface instead of the vehicle ahead. The change at the sensor is small, but it grows with distance down the road.
Changes that can affect sensor aim
- Lift kits, leveling kits and spacer lifts
- Lowering springs, coilovers and air suspension adjustments
- Tire and wheel size changes that alter ride height
- Replacing springs, struts, shocks or control arms
- Suspension repairs after a collision or pothole damage
- Ride-height sensor replacement on vehicles with adaptive headlights or air suspension
The link to wheel alignment
Many ADAS systems use the vehicle's thrust line, the direction the rear wheels push the vehicle, as their reference for straight ahead. Suspension work usually means a wheel alignment, and an alignment can change that thrust line. That is why manufacturers often list alignment and suspension work together as triggers for a calibration or a calibration check. The alignment should be completed first, because calibrating a sensor to an incorrect thrust line builds that error into the system.
Modified vehicles and manufacturer procedures
Calibration procedures are written for the vehicle as designed. Some manufacturers specify ride-height measurements as part of the setup, and a vehicle that sits well outside the designed range may not be able to complete a procedure, or may complete it but not behave as intended. Modified vehicles should be assessed case by case. We'll tell you before the appointment if the procedure for that vehicle has requirements a modified vehicle may not meet.
What to do before calibration
- Finish all suspension, lift or lowering work, and let the vehicle settle as the installer advises
- Complete a wheel alignment to the specification that applies
- Fit the tires that will stay on the vehicle and set the pressures
- Remove unusual loads, tools or equipment from the vehicle
- Scan the vehicle so any existing faults are known first
Signs the systems need attention after suspension work
- Lane-keeping that pulls toward one side or reacts late
- Adaptive cruise that loses the vehicle ahead or reacts to overhead objects
- Camera or radar warnings, or features showing as unavailable
- Automatic high beams or traffic-sign recognition behaving differently
Which systems are usually involved
The forward camera and the front radar are the systems most often affected by ride-height changes, because they look far ahead where small angles matter most. Rear and surround-view cameras can also be affected, since they're set up to show guide lines at specific distances around the vehicle. On some vehicles the steering angle sensor needs a reset after alignment as well. The repair information for the vehicle lists which systems apply.
Calibration after suspension work with AdasX
AdasX calibrates on-site at repair shops, tire and alignment businesses and dealerships in Mississauga, Oakville and Burlington. Forward camera calibration starts from $299 and radar calibration from $349, with multi-system work quoted per vehicle. Send the vehicle details and the suspension work performed, and we'll confirm what the procedure requires.
Tire size and pressure
Tire size is easy to overlook. Larger or smaller tires change ride height, and on some vehicles they also change how the vehicle calculates speed and distance travelled, which some ADAS functions use. Procedures commonly require tires at the specified pressure and of the same size all round. If the tire size has changed from the original specification, mention it when you book so we can check the procedure's requirements.
What to expect when you book
- Send the vehicle details: make, model, year, VIN if available, and the repair performed.
- We confirm compatibility, the required procedure, pricing, location and appointment availability.
- We arrange on-site service at your approved business location, with the space and conditions the procedure needs.
- We complete the applicable calibration procedure and provide the service documentation available for that vehicle.
Documentation
We complete the applicable calibration procedure and provide the service documentation available for that vehicle.
Frequently asked questions
Do I need ADAS calibration after installing a leveling kit?
It depends on the vehicle and the manufacturer. A leveling kit changes the angle of the front sensors relative to the road, and some manufacturers call for calibration after ride-height changes. The repair information for the vehicle decides.
Can a lifted truck be calibrated?
Often, but not always. Procedures are written for the vehicle as designed, and some include ride-height checks. A vehicle far outside the designed range may not complete a procedure, so we assess modified vehicles before booking.
Should alignment or calibration be done first?
Alignment first. Many systems use the vehicle's thrust line as their reference, so the alignment needs to be correct before a sensor is calibrated to it.
Does replacing shocks or struts affect ADAS?
It can if the ride height or alignment changes. Many suspension repairs are followed by an alignment, and the manufacturer's information shows whether calibration is needed afterwards.